IEC 60529-1 PDF

IEC DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE). operational equipment) must, according to IEC , belong to a specific type of protection. The types of pro- tection are also called IP codes. The abbreviation. IEC & NEMA Standards. ENCLoSurE ProTECTIoN rATINg SySTEMS. The International Electrotechnical Commission (IEC) has established an.

Author: Shanris Tusho
Country: Nepal
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 2 February 2008
Pages: 305
PDF File Size: 5.66 Mb
ePub File Size: 14.64 Mb
ISBN: 200-5-11542-684-4
Downloads: 41529
Price: Free* [*Free Regsitration Required]
Uploader: Shashura

Product Details For checking the protection against water to prove the degrees of protection with the second number X1.

Category:IEC 60529

Attention is particularly drawn to the following: However, the tests establishing compliance with any one of the lower degrees of protection need not necessarily be carried out provided that these tests obviously would be met if applied. Unless otherwise specified in a relevant product standard, the test samples for each test shall be in a clean and new condition, with all 600529-1 in place and mounted in the manner stated by the manufacturer. The first digit shows the extent to which the equipment is protected against particles, or to which persons are protected from enclosed hazards.

The tests are specified in clause A complete integrated system!

The counterbalanced 605229-1 is removed from the spray nozzle and the enclosure is sprayed from all practicable directions. It features 3 of our devices!

Copyright BIS has the copyright of all its publications. If an enclosure provides different degrees of protection for different intended mounting arrangements, the relevant degrees of protection shall be indicated by the manufacturer in the instructions related to the respective mounting arrangements. Your contact information will only be used by our company, and you can unsubscribe from our emails at any time.

Category:IEC 60529

International Standard IEC Conversely, an enclosure which protects equipment against ingress of particles will also protect a person from potential hazards within that enclosure, and this degree of protection is also defined as a standard. Product Details Designed to sit on top of the specimin grate of our drip box systems. Where appropriate, such a standard should also specify the method of marking which is to be used when – one part of an enclosure has a different degree of protection to that of another part of the same enclosure; – the mounting position has an influence on the degree of protection; – the maximum immersion depth and time are indicated.

  D400 NPN TRANSISTOR DATASHEET PDF

In the case of the test for the additional letter B, the jointed test finger may penetrate to its 80 mm length, but the stop face 0 50 mm x 20 mm shall not pass through the opening. If an extraction rate of 40 to 60 volumes per hour is obtained the duration of the test is 2 h. Product Details Designed to test for insect ingress. The protection against the ingress” of solid foreign objects 605229-1 that the object probes up to numeral 2 in table 2 shall not fully penetrate the enclosure.

Such exceptional cases shall conform with the requirements of this, basic safety standard and the product standard shall state clearly the additional procedure to be cafried out during tests for such a classification. The total flow rate is adjusted as specified in table 9 and is measured with a flow meter. The 6052-1 under test is placed in its normal operating position under the drip box the base, of 605299-1 is larger than that of the enclosure. Immersed at depth of 1mThe effect of temporary immersion in 60529–1 in depth mentioned by manufacturerThe effect of continuous immersion in waterIPX9-High pressure and temperature ic jets.

To carry and rotate the specimens when determining the protection against water. NOTE The attention of relevant technical committees is drawn to the fact that in some types of electrical equipment the maximum voltage produced internally r.

Measurement data is available 6059-1 an additional fee, padded protective case included and tech support are included. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing the result of a test, shall be rounded off in accordance with IS 2: Other letters may be used in product standards.

  DRUK KRS-Z30 PDF

Electrical installations of buildings IEC This may necessitate tests being done under both conditions. The tests for the second characteristic numeral are carried out with fresh water. This standard is also applicable to empty enclosures provided that the general test requirements are met and that the selected degree of protection is suitable for the type of equipment to be protected.

Category:IEC – Wikipedia

Gracie May 28, In the absence of a specification the acceptance conditions of this standard shall at least apply. IP An enclosure with this designation IP Code 2 – protects persons against access to hazardous parts with fingers; – protects the equipment inside the enclosure against ingress of solid foreign objects having a diameter of 12,5 mm and greater; 3 – protects the equipment inside the enclosure against the harmful effects, due to water sprayed against the enclosure; C – protects persons handling tools having a diameter of 2,5 mm and greater and a length not exceeding mm against access to hazardous parts the tool may penetrate the enclosure up to its full length ; S – is tested for protection against harmful effects due ;to the ingress of water when all the parts of the equipment are stationary.

Manufacturer must be consulted to determine the degree of protection. For example, such higher protection may be provided by barriers, suitable shape of openings or distances inside the enclosure.